GFCI Line vs Load: Which Wires Go Where (and Why It Matters)

GFCI Line vs Load: Which Wires Go Where (and Why It Matters)

Protect your Twin Cities home from power surges

On a GFCI outlet, the LINE terminals are where power comes in from the panel, and the LOAD terminals send protected power on to other outlets downstream. The incoming wires from the breaker always go on LINE. If you swap them, the outlet may look normal and even trip when you press TEST, yet fail to protect you. Here is how line and load on a GFCI work and how to tell them apart.

Reviewed by John Ihle, MN Master Electrician AM005101 · Three Rivers Electric

What line and load mean

A GFCI (ground-fault circuit interrupter) compares the current going out on the hot wire to the current returning on the neutral. If a small amount leaks, for example through a person, it opens the circuit in a fraction of a second. The device has two sets of terminals:

  • LINE: the supply side. A Leviton instruction sheet describes it as delivering power from the service panel to the GFCI.
  • LOAD: the downstream side. It delivers power from the GFCI to other receptacles on the circuit, giving them GFCI protection too.

Most receptacle GFCIs ship with a yellow sticker over the LOAD terminals so you do not use them by accident. Leave it on unless you are intentionally feeding other outlets.

Why the connection matters

Wiring What happens Is the outlet protected?
Power on LINE, nothing on LOAD Protects only that outlet Yes
Power on LINE, downstream wires on LOAD Protects that outlet and everything downstream Yes, including downstream outlets
Power wires on LOAD, nothing on LINE Many devices will not reset, or reset but give no protection No
Downstream wires on LINE, power on LOAD Same reversal; downstream outlets may be powered but unprotected No

Leviton’s instructions warn that if you connect the incoming wires to the LOAD terminals, the device will not reset. The U.S. Consumer Product Safety Commission has also documented the problem. In a 2001 staff position paper, CPSC reported that receptacle GFCIs are often installed with line and load reversed, leaving the outlet without shock protection even though a miswired unit may still trip when TEST is pressed. Newer devices are designed to reduce that risk, but older units and some replacements can still be miswired.

How to tell which wires are line and which are load

This is information to help you understand a problem, not an invitation to open a panel or an outlet box yourself. Identifying wires means testing live conductors, and that is work for a licensed electrician.

  1. The wire pair that comes from the panel is the supply, or line. In a chain of outlets, the first outlet is the one closest to the panel.
  2. The wire pair that runs onward to other outlets is the downstream, or load.
  3. If both pairs are in the box and you cannot tell which is which, an electrician uses a tester with the power on to find the supply pair, then lands it on LINE.

GFCI to GFCI wiring

You do not need to feed one GFCI outlet from another GFCI outlet’s LOAD terminals. A single GFCI at the start of a run can protect everything after it. When two GFCI devices are chained on one run, they each trip independently, and nuisance trips are a common complaint. Usually the better design is one GFCI protecting the downstream outlets, or a GFCI breaker in the panel. We compare the two in GFCI vs AFCI outlets in the Twin Cities.

How to test whether protection is working

The manufacturer’s instruction sheet gives a simple check: with a lamp plugged in and the outlet on, press TEST. The lamp should go off and the GFCI should stay tripped. Press RESET, and the lamp should come back on. If the indicator light is on while the lamp is off and the device will not reset, the line and load connections may be reversed. Press TEST and then RESET once a month to confirm it still works. Downstream outlets should also lose power when you press TEST; if they do not, they are not on the LOAD side.

Because a miswired outlet can still click when tested, a plug-in GFCI tester is a useful extra check, but it does not replace an inspection by an electrician.

When a GFCI will not reset

A GFCI that will not reset might have reversed wiring, a real ground fault downstream, moisture in an outdoor box, or simply be worn out. We walk through the causes in why a GFCI won’t reset. If the outlet is hot to the touch, smells, or sparks, stop using it and call a licensed electrician.

Why we do not recommend DIY on this

Replacing a GFCI looks easy, which is exactly why it is so often done wrong. A reversed or loose connection can leave a bathroom, kitchen, garage, or outdoor outlet with no protection against shock. In Minnesota, electrical work generally requires a permit, and while the state lets homeowners request permits for their own property, we recommend a licensed electrician for anything involving wiring. See the Department of Labor and Industry homeowner page. Terms like GFCI, AFCI, line, and load are defined in our electrical glossary.

Ready to get started? Call Three Rivers Electric at 651-418-1476 or request a quote. We are a licensed Twin Cities electrical contractor (MN EA761814) and we pull the permits for the work we do.

Frequently asked questions

Which wires go on line and which go on load on a GFCI?

The wires coming from the electrical panel, the power supply, go on the LINE terminals. Wires running on to other outlets go on the LOAD terminals, and the outlet only uses LOAD if you want those downstream outlets protected. If you only need one outlet protected, use LINE only.

What happens if you reverse line and load on a GFCI?

Many devices will not reset, or may reset but not protect the outlet. The Consumer Product Safety Commission has noted that a miswired GFCI can still trip on the TEST button, giving a false impression of protection. A licensed electrician should correct the wiring.

Do I have to use the load terminals?

No. If you connect only the LINE terminals, the outlet itself is protected and nothing else. LOAD terminals are optional and used when you want the GFCI to protect other receptacles downstream. Leave the protective sticker over LOAD if you are not using it.

Can you wire one GFCI to another GFCI?

You can, but you generally do not need to. A single GFCI placed first in the run protects every outlet after it when those outlets are wired from its LOAD terminals. Chaining GFCIs can cause confusing nuisance trips, so ask your electrician for the cleanest layout.

How often should I test a GFCI outlet?

Manufacturers recommend pressing TEST and then RESET every month. The outlet should lose power when you press TEST and restore it when you press RESET. If it does not trip, will not reset, or protects nothing downstream, have a licensed electrician inspect it.

Sources